ProFlow Water softener Manuel de service télécharger pdf (Page 7)

INSTALLATION

Page 7

INLET & OUTLET

 Check the water pressure at the place of installation of

the water softener; it should never exceed 8,3 bar.

 In case of high concentration of impurities in the inlet

water, we recommend the installation of a sediment filter,

ahead of the water softener.

 We strongly recommend the use of flexible hoses to

connect the water softener to the water distribution system;

use hoses with a large diameter in order to limit the pressure

loss.

 We strongly recommend the installation of a bypass

system (not included with this product!) to isolate the water

softener from the water distribution system in case of

repairs. It allows to turn off the water to the water softener,

while maintaining full-flow (untreated) water supply to the

user.

 In case of a Duplex/Triplex system, we strongly

recommend to keep the inlet and outlet plumbing to all

Simplex systems as identical as possible; this way the total

water flow is evenly spread over the different Simplex

systems.

SIMPLEX

with factory bypass (optional)

Picture 2

 = mains water supply (hard/untreated water)

 = inlet of water softener (untreated water)

 = outlet of water softener (treated water)

 = application (treated water)

1. Screw the factory bypass onto the in/out ports on the

control valve (&); make sure to install the gasket

seals. Tighten the nuts firmly by hand.

2. Screw the connection kit with nuts onto the factory

bypass (&); make sure to install the gasket seals.

Tighten the nuts firmly by hand.

3. Connect the mains water supply to the adaptor on the

inlet port of the factory bypass ().

4. Connect the application to the adaptor on the outlet port

of the factory bypass ().

SIMPLEX

with 3-valve bypass (not included)

Picture 3

 = inlet of water softener (untreated water)

 = outlet of water softener (treated water)

1. Install the 3-valve bypass system.

2. Screw the connection kit with nuts onto the in/out ports

on the control valve (&); make sure to install the

gasket seals. Tighten the nuts firmly by hand.

3. Connect the IN valve of the 3-valve bypass system to the

adaptor on the in port () of the control valve.

4. Connect the OUT valve of the 3-valve bypass system to

the adaptor on the out port () of the control valve.

5. Connect the mains water supply to the inlet of the 3-valve

bypass system.

6. Connect the application to the outlet of the 3-valve

bypass system.

DUPLEX ALTERNATING/PARALLEL

with multiple valve bypass (not included)

Picture 4

 = inlet of water softener (untreated water)

 = outlet of water softener (treated water)

 = Service Valve

1. Install the multiple valve bypass system.

2. Screw the connection kit with nuts onto the in/out ports

on the control valve (&); make sure to install the

gasket seals. Tighten the nuts firmly by hand.

3. Screw the Service Valve () onto the adaptor () at the

out port of the control valve; make sure to respect the

flow direction (see indication arrow on the bottom of the

Service Valve); use an appropriate sealant.

4. Connect the IN valve of the bypass system to the adaptor

on the in port () of the control valve.

5. Connect the OUT valve of the bypass system to the

Service Valve ().

6. Repeat steps 2-5 for both Simplex systems.

7. Connect the mains water supply to the inlet of the

multiple valve bypass system.

8. Connect the application to the outlet of the multiple valve

bypass systems.

TRIPLEX PARALLEL

with multiple valve bypass (not included)

Picture 5

 = inlet of water softener (untreated water)

 = outlet of water softener (treated water)

 = Service Valve

1. Install the multiple valve bypass system.

2. Screw the connection kit with nuts onto the in/out ports

on the control valve (&); make sure to install the

gasket seals. Tighten the nuts firmly by hand.

3. Screw the Service Valve () onto the adaptor () at the

out port of the control valve; make sure to respect the

flow direction (see indication arrow on the bottom of the

Service Valve); use an appropriate sealant.

4. Connect the IN valve of the bypass system to the adaptor

on the in port () of the control valve.

5. Connect the OUT valve of the bypass system to the

Service Valve ().

6. Repeat steps 2-5 for all Simplex systems.

7. Connect the mains water supply to the inlet of the

multiple valve bypass systems.

8. Connect the application to the outlet of the multiple valve

bypass systems.

QUADPLEX PARALLEL (= 2 x DUPLEX)

with multiple valve bypass (not included)

Picture 6

1 2 3 4 5 6 7 8 9 10 11 12 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

ProFlow Water softener Manuel de service Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Distributeurs d'eau ProFlow Water softener